« Back to the stripboard layouts

Battery Breakout

Two 9V batteries, one power header · Test a module before the case arrives · Takes no HP · By Onion Madder · Mess O' Pedals

Every module on this shelf wants ±12 V on a ten-pin header, and until there is a case with a power supply in it there is nothing to plug one into. This is the way to bring a module up anyway: two 9V batteries in series make ±9 V, and this little board puts it on the same 2×5 header the modules take. A battery cannot be plugged in backwards at the wall, cannot push much current into a short on a fresh board, and floats free of everything else on the bench - and every module here has a 1N5817 in each rail anyway. It takes no HP and has no panel; it sits on the bench at the other end of a ribbon.

The Battery Breakout layout drawn as a stripboard diagram, titled Battery Breakout, 14 by 5 stripboard. Five orange copper strips lettered a to e run left to right with fourteen columns numbered above them. Near the left two short dark blue links join strips b, c and d, and two pink circles mark the electrolytics C1, between strips a and b, and C2, between strips d and e. Holes carrying wires off the board are labeled in the left margin: plus V on strip a, GND on strip c and minus V on strip e. The ten header pins H1 to H10 sit in two columns in the middle of the board, two to a strip, labeled in both margins, H9 and H10 on strip a and H1 and H2 on strip e. On the right, the resistors R1 on strip a and R2 on strip e each lie along their strip across a gray cut mark, and two red circles at the right edge are the LEDs D1, between strips a and b, and D2, between strips d and e. To the left of the board two 9 volt battery snaps, BT1 and BT2, and the two poles of the DPDT power switch, SW1 and SW2, are drawn with a wire to each pad. Below, the same board is drawn again from the solder side, mirrored, with every solder point as a dot and the cuts as X marks, then a parts list and an Off the board block listing where each panel part lands.
The board as the layout file draws it, with the batteries and the switch beside it. The lower drawing is the solder side, mirrored - the side you actually work on.
The Battery Breakout built on a small piece of stripboard, lying on a dark bench. The board carries the two-row header pins in the middle, two small black electrolytic capacitors near one end, and two blue resistors running toward the other end, where both LEDs are lit. Red and black leads run from the board to two 9 volt batteries lying side by side behind it.
Built and working, on the bench in October 2026, without the power switch: the battery leads go straight onto the board. Both rail LEDs lit: both batteries are in, the right way around.

What you'll need

tap to expand / collapse

On the board, counted from the layout file:

  • 2× 4k7 (yellow-violet-red; R1, R2) - one for each rail LED, lying along its strip across a cut
  • 2× 10u electrolytic (C1 to C2) - spot it: the stripe marks the negative leg
  • 2× LED, any color (D1, D2) - spot it: the long leg is the anode. D1 lights for the + battery, D2 for the - one
  • 2 wire links (J1 to J2) - solid core, tinned
  • 1× 2×5 pin header, plain, 0.1″ - the Eurorack power connector. spot it: ten square pins in two rows. Not the shrouded kind; a shroud is 20 mm long and would cover the neighboring strips
  • Stripboard, 5 strips × 14 holes or larger

Off the board

  • 2× 9V battery and battery snap - red lead plus, black lead minus
  • 1× DPDT toggle, the power switch, one pole per battery - an on-on DPDT works, using the middle lug and one end of each pole
  • 1× 10-pin to 10-pin Eurorack power ribbon - not a 16-pin one, see the note below

What it is

Five strips, one rail each. The header stands with its pins down the strips, the way every module here takes it, so each pin pair lands on one strip: +V on top for the +12 pins, three joined ground strips in the middle, and -V on the bottom strip, H1 and H2, the red stripe end. A 10 µF steadies each rail. An LED on each rail, through a 4.7K on its own island past a cut, lights only if that battery is in and the right way around, so the check before the ribbon goes on is two lights. Off the board, one DPDT toggle switches both rails together, so a module never sees one rail without the other.

Use a 10-pin to 10-pin ribbon. A 16-pin plug can sit on a 10-pin header one row out, and that puts the rails on the wrong pins. Nothing taller than a flat link stands under the ribbon's socket, so it pushes straight down.

The layout file is the guide

As on every stripboard guide here, the build document is the file itself: ↓ Download Battery_Breakout.json - import it into Copper Bottom and the editor gives you the board picture, the placement walkthrough, the electrical checks and a printable build sheet, all from the same file. No coordinates are written out on this page on purpose: the editor is the viewer, and a number typed twice is a number that can drift.

The netlist

tap to expand / collapse

Quoted verbatim from the layout file. It was written from the design, so the editor's check that the board matches it compares two separate records - what it is for is carrying the circuit somewhere else, and telling you what each strip is supposed to be doing while you stare at it. The three rails are named for what they carry.

The off-board wiring

13 pads leave the board. Ten of them are the power header.

PadGoes to
+VThe DPDT's first pole, common lug. That pole's other lug takes the first battery's red lead
-VThe DPDT's second pole, common lug. That pole's other lug takes the second battery's black lead
GNDThe middle of the two batteries: the first battery's black lead and the second battery's red lead, joined here
H1 … H10The power header itself. Nothing leaves the board here; the ribbon plugs onto it. H1 and H2, the red stripe, are -V, on the bottom strip

Bringing a module up on it

Will ±9 V run them? Yes, for a first test. The Hive, Cicada, Grub and Spider run their CMOS from their own 78L05 at 5 V, which wants about 7 V in; 9 V less the module's 1N5817 is plenty, so the pitches should be where they would be in the rack. The TL072 and TL074 stages on every module swing a little less than they will on ±12 V. The Envelope uses only the positive rail.

  1. Before any power, meter the module: resistance across each rail to ground and between the two rails. Near zero is a short; find it first. Then diode-test each 1N5817: about 0.2 to 0.3 V one way, open the other
  2. Switch the breakout on with nothing plugged in. Both LEDs lit means both batteries are in the right way around
  3. First power-up with the meter in series in one battery lead, on its milliamp range. Tens of milliamps is right; hundreds means switch off and look for the short
  4. Measure the rails on the module: about +8.7 and -8.7 V after its diodes, and 5.0 V on the 78L05 where there is one
  5. Listen with the amp turned all the way down. Rack level is around ten volts peak to peak, far hotter than a guitar

How it works, in one breath

Two batteries in series, and the point between them is ground: the top of one is +9 V and the bottom of the other is -9 V. That is all a bipolar supply is. Each LED runs from its rail to ground through 4.7K, about 1.5 mA, enough to see and not enough to matter to the batteries; a module or two draws tens of milliamps, so a fresh pair is many hours of bench time. All of that is arithmetic, not measured.

Things to try

  • Two modules at once. A ribbon with several sockets on it feeds more than one; keep the total to a few tens of milliamps and watch the batteries
  • Darker LEDs. 10K instead of 4.7K halves their current if the batteries matter more than the lights
  • Retire it. Once the case is up, this is still the board to bring a brand-new module up on before it goes near the rest

The same circuit on a breadboard

tap to expand / collapse

Want to hear it before you solder it? This is the layout file above moved onto a half-size breadboard, 30 columns by Copper Bottom's to breadboard button, in 22 steps with exact holes. It is a translation, not a copy: a strip and a breadboard column are different shapes, so every part is placed fresh and the stripboard's wire links are not needed.

Checked by the app, not built by me. Copper Bottom rebuilt the connections from these holes alone and compared them with the stripboard: all 25 terminals land on the same nets. Nobody has built this breadboard version.

Note. -V is a negative supply. A breadboard has a + rail and a - rail, so this net rides ordinary columns - double-check it against the rails.

Turn the board so the numbers climb left to right. Then A to E is the lower bank, F to J the upper, the top rails are above J and the bottom rails below A.

Battery Breakout drawn on a half-size breadboard, 30 columns by Copper Bottom. The picture shows each part and jumper between lettered and numbered holes, with the rails along the top and bottom. Every hole in it is written out in the steps below.
Battery Breakout on a breadboard, generated from the layout file. The steps below name every hole in it.

The semiconductors

On a breadboard: The semiconductors
StepDo
1Diode D1 (LED): C2 to bottom − rail.
The SECOND hole named gets the banded end - the cathode. Backwards, nothing works at all.
2Diode D2 (LED): bottom − rail to C3.

Jumpers

On a breadboard: Jumpers
StepDo
3Jumper: B5 to E6 (@H2 to @-V).

Resistors

On a breadboard: Resistors
StepDo
4Resistor R1 (4k7): bottom + rail to B2.
5Resistor R2 (4k7): B6 to B3.

Electrolytics

On a breadboard: Electrolytics
StepDo
6Cap C1 (10u): + leg into the bottom + rail, − leg into the bottom − rail.
The stripe on the can marks the MINUS leg. Backwards, an electrolytic eventually vents.
7Cap C2 (10u): + leg into the bottom − rail, − leg into C6.

Off-board

On a breadboard: Off-board
StepDo
8Wire for -V: into A6.
This is where SW2 common: the - battery, switched joins the board.
9Wire for H1: into D6.
This is where header pin 1 - the RED STRIPE end, -V joins the board.
10Wire for H2: into A5.
This is where header pin 2 - the RED STRIPE end, -V joins the board.
11Wire for H3: into the bottom − rail.
This is where header pin 3 joins the board.
12Wire for H4: into the bottom − rail.
This is where header pin 4 joins the board.
13Wire for H5: into the bottom − rail.
This is where header pin 5 joins the board.
14Wire for H6: into the bottom − rail.
This is where header pin 6 joins the board.
15Wire for H7: into the bottom − rail.
This is where header pin 7 joins the board.
16Wire for H8: into the bottom − rail.
This is where header pin 8 joins the board.
17Wire for H9: into the bottom + rail.
This is where header pin 9 joins the board.
18Wire for H10: into the bottom + rail.
This is where header pin 10 joins the board.

Power up

On a breadboard: Power up
StepDo
19+V - SW1 common: the + battery, switched: clip to the bottom + rail.
20GND - BT1 minus and BT2 plus, joined: the middle of the two batteries: clip to the bottom − rail.
21Before the battery: meter on continuity.
rail to rail reads open, not a short
B5 to E6 beeps (@H2 to @-V)
22Power on.

Translated by Copper Bottom v1.7.29 from Battery_Breakout.json.

Two batteries in series as a split supply is as old as op-amps. The header follows Doepfer's bus standard, as every module here does. Drawn and checked in Copper Bottom.