« Back to the Eurorack modules

Learn to Build a Module

From a zip of gerber files to a Eurorack module making sound · By Onion Madder · Mess O' Pedals

A lot of DIY Eurorack modules are shared as gerber files: a zip that a board maker turns into real printed circuit boards. This guide walks the whole trip, start to finish: getting the files, uploading them, ordering, soldering, testing, and getting the module to make a sound in a rack.

It is not about one module. It works for any through-hole module whose designer publishes gerbers and a parts list, and the ordering half works for any board at all, pedal boards included. If you would rather skip the board maker entirely, every one of the Eurorack modules is drawn on stripboard instead.

⚠ Before you start tap to expand / collapse
  • A backwards power cable kills modules. Eurorack power is ±12 V, and swapping +12 and −12 puts 24 V the wrong way through every chip. The red stripe goes to −12 V, at both ends, every time. Step 6 has the check.
  • Never plug or unplug a module with the case on. Power off, then cables.
  • The first power-up goes through something that limits current, not straight into the case. A short on a fresh board then gets warm instead of burning a trace.
  • Solder fumes and flux: work with air moving, and wash your hands after handling leaded solder.

What you'll need

tap to expand / collapse

The module's own parts list says what goes on the board. This is everything around it. Each line notes how to spot it.

  • The module's files: the gerber zip, the parts list (BOM), and the panel file if the panel comes separately. Spot it: the gerbers are a .zip with files ending .gtl, .gbl, .gto, .drl and so on inside
  • The parts on that list. Order a few spares of the cheap ones: resistors and small caps go missing on the floor
  • A Eurorack power cable, usually 10-pin at the module end and 16-pin at the case end. Spot it: a flat gray ribbon with one red stripe down one edge
  • Soldering iron, temperature controlled if you can, with a small chisel tip
  • Solder: thin, 0.6 to 0.8 mm, with flux in the core
  • Flush cutters for trimming legs
  • Multimeter with a continuity beep. Spot it: the dial position with a little speaker or sound-wave symbol
  • Something that limits current for the first power-up: a bench supply with a current limit, or the Battery Breakout, two 9V batteries on the same 10-pin header the modules take
  • A case with a power supply, and room in it: modules are measured in HP, and 1 HP is 5.08 mm
  • M3 rack screws, usually 6 mm long, two or four per module
  • Optional: flux pen, isopropyl alcohol and an old toothbrush for cleaning flux off

Quick reference - the power header

The one connector that has to be right. Every Eurorack module uses this pinout; the red stripe is pin 1.

Red stripe to −12 V. On the board, −12 V is marked -12V, a white bar, a stripe, or the word RED beside the header. Check the case's bus board the same way.

Soldering order

  • Resistors, diodes
  • Small ceramic caps, chips
  • Film caps, transistors, trimmers
  • Electrolytics, power header
  • Jacks, pots, switches, LEDs: panel ON first

Before it meets the case

  • Look at every joint
  • Beep +12 to GND, −12 to GND, +12 to −12: no steady beep
  • Power it through a current limit
  • Rails at the chips: about +12 and −12
  • Nothing hot to the touch

Step 1 Get the gerbers

The designer's page, or their GitHub, will have a download for the board files. You want three things:

  • The gerber zip. Each file in it is one layer of the board: the copper on top and bottom, the solder mask (the colored coating), the silkscreen (the white printing), the drill holes and the outline. Do not unzip it. Board makers want the zip exactly as it came.
  • The parts list, often called the BOM (bill of materials). It names every part by its reference on the board: R1, C3, U2.
  • The panel. Some modules ship the front panel as a second gerber zip, to be made as its own board; others give a drill template for a blank aluminum panel.

Before uploading, open the zip in a free gerber viewer (most board makers have one on their site, and KiCad's GerbView reads them too). You are checking that it looks like a board: an outline, holes where parts go, and readable part numbers. If the zip has more than one board in it, or the files sit inside a folder inside the zip, read the designer's notes before going further.

Check the license as well. Most open-source modules are fine to build for yourself; some say no selling, and that applies to the boards you have left over.

Step 2 Upload them to a PCB maker

JLCPCB, PCBWay, OSH Park and Aisler all take a gerber zip and post boards back. Find the upload or "instant quote" button, drop the zip on it, and the site reads the board size and layer count off the files by itself.

Look at the preview it draws. It should match what you saw in the viewer. A missing outline, a board the wrong size, or a blank silkscreen means the zip did not read right.

Then the settings. The defaults are usually right for a module; these are the ones worth reading:

  • Layers: leave it at what the site read, nearly always 2.
  • Quantity: 5 is the usual minimum. You will have spares to give away or wreck while learning.
  • Thickness: 1.6 mm, the standard. A panel made as a board is 1.6 mm too.
  • Color: your call. Green is often the cheapest and fastest; other colors can add days.
  • Surface finish: HASL is fine for through-hole parts. Lead-free HASL if you want the board lead-free. ENIG is the gold-looking finish: smoother, costs more, and does not tarnish, which is why it is popular on panels.
  • The order number: some makers print a tracking number on your board unless you choose otherwise. If the designer marked a spot for it, choose that; otherwise there is usually an option to leave it off.
  • Assembly and stencil: leave them off. Those are for the maker soldering parts for you, or for surface-mount parts.

If the panel is a gerber too, upload it as a second board, with its own settings.

Step 3 Order the boards and the parts

Pick a shipping speed and check out. The slow, cheap shipping can take weeks; the courier options take days and can cost more than the boards. Depending on where you live, import tax can come due on delivery.

Order the parts while the boards are being made. Most of a module comes from one big supplier (Tayda, Mouser, DigiKey and others), and the Eurorack-specific bits often from a synth shop. Two things to match carefully, because the board's holes only fit one kind:

  • Jacks. Most modules are drawn for the Thonkiconn (PJ398SM) 3.5 mm jack. A different jack will not fit its holes.
  • Pots. Check the size (9 mm or 16 mm), the shaft (knurled or D) and that the legs face the right way for a board: vertical pots for a board behind a panel.

When the boards arrive, look them over before you start: a scratch through a trace, or a board cut short, is the maker's problem and they will usually remake it if you send a photo.

Step 4 Solder it, lowest parts first

Go by height. The board sits upside down on the bench while you solder, so short parts go in first and are held in by the bench rather than falling out. Tick each part off the parts list as it goes in.

  • Resistors. No direction. Bend the legs, push them through, bend the legs out a little underneath so the resistor stays put, solder, trim.
  • Diodes. They have a direction. Spot it: the band on the diode matches the line on the board's printing.
  • Small ceramic caps (no direction) and the chips. A chip's notch or dot matches the notch in the board's outline. Solder one corner pin, check the chip is flat and the right way around, then do the rest, giving it a few seconds between pins so it does not cook.
  • Film caps, transistors and trimmers. A transistor's flat face matches the flat side of its outline on the board.
  • Electrolytic caps have a direction. Spot it: the stripe down the can is the minus leg, and the long leg is plus. The board marks one hole +, or shades the minus half.
  • The power header. If it is shrouded, its key slot matches the outline on the board. Hold it flat while you solder the first pin.
  • The panel parts last: jacks, pots, switches and LEDs. Push them into the board without soldering, fit the panel over them, and do the nuts up finger tight. Now solder them. That way every shaft lines up with its hole. LEDs: push them up to the panel, or to the height the designer gives, before soldering.

A good joint is shiny and shaped like a little volcano around the leg. A ball sitting on top has not wetted the pad: heat the pad and the leg together and feed the solder into them, not onto the iron.

Clean the flux off with isopropyl alcohol and a toothbrush if your solder leaves it sticky. It makes the next step easier, because you can see the joints.

Step 5 Test it before it meets the rack

Look. Under a good light, with a magnifier or your phone camera zoomed in, go over every joint. You are looking for two pads joined by a blob of solder, a pin with no solder at all, and any part in backwards. Check every chip, diode and electrolytic against the board one more time.

Beep the rails with the power off. Set the meter to continuity and touch the probes to the power header pins: +12 to GND, −12 to GND, and +12 to −12. A short chirp is fine, that is the big caps charging off the meter. A steady beep is a short: find it before going any further.

Power it through a current limit. On a bench supply, set the limit low, say 50 to 100 mA, and watch the current as you switch on. If it jumps straight to the limit, switch off and go hunting. The Battery Breakout does the same job with two 9V batteries, which cannot push much current into a short.

Measure the rails at the chips. Black probe on ground, red probe on each chip's power pins: you want about +12 V and −12 V there (about ±9 V on the battery breakout). If the module has a regulator for 5 V, check its output too. A rail that sags well under where it should be means something is pulling it down.

Touch. Run a finger near the chips, regulators and transistors after a minute. Warm is fine. Too hot to keep a finger on is not: switch off.

One thing a battery supply will not tell you: a module set up for ±12 V can behave differently on ±9 V. A tuned oscillator can sit lower in pitch, for one. Do the final tuning in the case.

Step 6 Rack it and make a sound

  • Case power off.
  • Cable into the module, red stripe to −12 V. A shrouded header only goes in one way; an open one goes in both, so look.
  • Cable into the case's bus board, red stripe to −12 V again. Bus boards are marked the same way, and not every one is shrouded. Trace the stripe from one end to the other with your finger.
  • Screw it in with M3 screws. Check the module is not deeper than the case, and that nothing on the back of the board touches the module next to it.
  • Case power on, and watch for anything odd: a power LED that goes out, a smell. If anything is wrong, off again.

Now patch it. Send its output to something you can hear at a low volume, like a mixer, an output module such as the Output Rack, or a pedal into an amp. Then go through its controls one at a time, and every jack. If it has trimmers to set, the designer's build notes say how; a 1 V/oct oscillator gets tuned against a tuner with the case warmed up.

Troubleshooting When it does not work

  • Nothing at all. Check the rails at the chips first, every time. No voltage means the header, the cable, or a protection diode in backwards.
  • The supply hits its limit at switch-on. A short, or a part in backwards: electrolytics, diodes and chips are the usual three. Beep the rails again with the chips in view.
  • One chip gets hot. Backwards, or a solder bridge on its pins. Switch off now.
  • Works, but one control does nothing. Look at that pot or jack's joints: the panel parts are the last ones soldered and the easiest to miss a leg on.
  • Crackle when you move a cable. A jack joint that is cracked or dry. Reflow it with a touch of fresh solder.
  • Something that should be stable drifts. Leftover flux can leak a little current on high-value parts. Clean the board.
  • Still stuck? Most designers have a build thread or a forum. Post clear photos of both sides of the board and the voltages you measured.

How it works, in one breath

A gerber file is a drawing of one layer of a board, and the zip is the stack: copper top and bottom, the solder mask that covers the copper you are not meant to solder, the silkscreen printed on top, the drill file that says where the holes go, and the outline that says where to cut. The maker etches the copper, drills and plates the holes so each one joins top to bottom, coats and prints it, and cuts it out. The parts you solder in finish the circuit; the power header brings it ±12 V from the case, and the panel holds the controls where your hands can reach them.

Going further

  • Build one on stripboard. Every one of the Eurorack modules comes as a layout file for Copper Bottom, with a 3U panel drill template. No board maker, no waiting
  • Draw your own board. KiCad is free and exports the same gerber zip this guide starts from
  • Build a case. Flavio Mireles's Survival page at Blue Lantern Modules builds a 3U + 3U + 1U case out of hardware-store pine

Written by Onion Madder for Mess O' Pedals.