Grubworks PCB v1.1
CD4024 + TL072 + 4× NE555 on a 93 by 71 mm printed board, marked GRUBWORKS v1.1 · By Onion Madder · Mess O' Pedals
Grubworks on its v1.1 board. Two voices, hum (an Opto Duet) and chew (an Atari Punk Console), clock a Grub Divider through a TL072 preamp, so the octave toggles pick which of seven divisions of the voices you hear. On this board the six pots go on the face on wires, each from a header of its own.
What you'll need
tap to expand / collapse
57 parts on the board. The numbers in brackets are the ones printed on the board, and so is each part's value. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.
- 1× CD4024 (U1) - spot it: CD4024 printed on top, a notch or dot marks pin 1. The divider
- 1× TL072 (U2) - spot it: TL072 printed on top, a notch or dot marks pin 1. The preamp. Any dual op-amp with the standard pinout goes in the same holes
- 2× NE555 (U3, U4) - spot it: NE555 printed on top, a notch or dot marks pin 1. Hum: U3 is the engine, U4 the voice
- 2× NE555 (U5, U6) - spot it: NE555 printed on top, a notch or dot marks pin 1. Chew: U5 runs free and sets the pitch, U6 fires on each of its ticks and sets the width
- 1× 1M resistor (R1) - spot it: bands brown-black-green. Octave 1
- 1× 470K resistor (R2) - spot it: bands yellow-violet-yellow. Octave 2
- 1× 220K resistor (R3) - spot it: bands red-red-yellow. Octave 3
- 1× 100K resistor (R4) - spot it: bands brown-black-yellow. Octave 4
- 1× 47K resistor (R5) - spot it: bands yellow-violet-orange. Octave 5
- 1× 22K resistor (R6) - spot it: bands red-red-orange. Octave 6
- 1× 10K resistor (R7) - spot it: bands brown-black-orange. Octave 7. R1 to R7 are the weighted ladder, every value different: they are what make this a mixer and not a selector
- 1× 1M resistor (R11) - spot it: bands brown-black-green. Holds the preamp's input at the half rail
- 5× 100K resistor (R8, R9, R12, R14, R15) - spot it: bands brown-black-yellow. R8 and R9 are the clock and reset pull-downs, R12 the preamp's feedback, R14 and R15 the half rail
- 2× 10K resistor (R22, R23) - spot it: bands brown-black-orange. The two that sum the voices
- 1× 2.2K resistor (R25) - spot it: bands red-red-red. The power LED's resistor
- 9× 1K resistor (R10, R13, R16, R18, R20, R21, R24, R26, R27) - spot it: bands brown-black-red. R10 on the output, R13 the floor under GAIN, R16 and R18 hum's timing chains, R20 and R21 the floors under hum's TEMPO and PITCH, R24 chew's tempo stop, R26 and R27 the floors under chew's pots
- 2× 100R resistor (R17, R19) - spot it: bands brown-black-brown. Hum's two outputs, where they mix
- 1× 2.2nF ceramic (C7) - spot it: printed 222. The tracking cap
- 3× 10nF ceramic (C9, C12, C17) - spot it: printed 103. C9 and C12 on hum's pin 5s, C17 chew's timing cap
- 7× 100nF ceramic (C1, C6, C11, C15, C16, C18, C20) - spot it: printed 104. C11 is hum's voice timing cap and C18 chew's width timing cap; the rest sit across the supplies
- 1× 100nF film or other non-polarized cap (C3) - spot it: a small box, printed 104. The input cap, a film one
- 5× 10 µF electrolytic (C2, C4, C5, C8, C19) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. C8 is hum's engine timing cap; C2 and C19 output caps; C4 in the gain leg; C5 holds the half rail still
- 4× 100 µF electrolytic (C10, C13, C14, C21) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. Hum's two output caps, and two across the supplies
- 1× 1N5817 (D1) - spot it: black body, gray band. The band goes to the square pad, the end the board marks with a band and a K. Reverse-polarity protection; every stage takes its supply through it
- 1× LED (LED1) - The vactrol's LED, beside LDR2. It runs bare, no resistor, as on the Opto Duet. The short leg, on the flat side of the rim, goes in the square pad
- 1× photocell, an LDR (LDR2) - The vactrol's cell, beside LED1. Either way around
- 1× Grubworks PCB v1.1
Off the board
- 1× DC jack and a 9V supply, center negative. The Opto Duet wants 6V and up, or its LED stops flashing
- 1× SPST toggle for power, between the DC jack's + lug and SW
- 2× B100K pots, GAIN and VOLUME, on wires to their headers
- 2× 100K pots, HUM TEMPO and HUM PITCH, on wires to their headers
- 2× B500K pots, CHEW TEMPO and CHEW WIDTH, on wires to their headers
- 2× SPST toggles, hum on and chew on
- 7× SPST toggles, one per octave
- 1× SPST toggle for TRACK
- 2× 3.5 mm jacks: the output, and EXT IN, which must be a switched jack, one with a third lug that touches the tip with nothing plugged in
- 1× LED for power, on J8
- 1× LED for hum, on HUM LED
- Hookup wire
What changed from v1.0
- The pots are off the board. On v1.0 six 16 mm pots soldered to the board, too close together. Each is now a three-pin header along the bottom edge, marked 1, W and 3 with the pot's name and value, and the pot goes on the face on wires.
- Every octave toggle has its own BUS pin. J3 is fourteen pins, 1 B 2 B and so on to 7 B: each numbered pin has a B beside it, and every B is the same BUS, joined on the board. Each toggle takes two wires to two holes of its own. On v1.0 all seven toggles shared one BUS hole.
- Every header pin has its label over it. On v1.0 J3's numbers drifted off their holes.
- The hum LED is on a header, HUM LED, marked - and +, so it can sit on the face.
- The resistors lie flat. On v1.0 all twenty-seven stood on end.
- JP1 still bypasses the preamp. Leave the TL072 out and short JP1, and the voices go to the divider's clock with no gain stage. Decide before you solder the chip in.
- The ceramic caps' holes are 5.08 mm apart, not 2.5, so a dipped ceramic drops in flat with no leg to kink.
- Every value is printed on the board, on the part's outline or beside it, with its number.
- Four M3 mounting holes, since the pots no longer hold the board. The board is 93 by 71 mm, from 86 by 100.
The headers
Everything that leaves the board leaves from a header, and each one has its pins labeled on the board. The square pad is pin 1, the first one named here.
| Header | Pins | Goes to |
|---|---|---|
| J1 | DC+ / SW / GND | Power, wired the usual way: the DC jack's + lug to one lug of the power toggle, the toggle's other lug to SW, and the jack's - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. SW is the board's power input, through D1, which guards against a supply plugged in the wrong way around. DC+ connects to nothing on the board: it is a spare pad to join the jack's + and the toggle on, if that is easier, and it can stay empty |
| J8 | LED+ / - | The power LED: its long leg to LED+ and its short leg to -. Its resistor, R25, is on the board |
| J2 | HUM / + / CHEW | The two voice toggles. Each one's middle lug to +, and its other lug to HUM or CHEW |
| J3 | 1 B 2 B 3 B 4 B 5 B 6 B 7 B | The octave toggles. Each toggle goes across a numbered pin and the B pin beside it. Every B is the same BUS |
| J5 | TIP / SW / GND | EXT IN, a switched jack: tip to TIP, the switched lug to SW, sleeve to GND. Unplugged, the preamp hears both voices; a plug overrides them |
| J4 | OUT / GND | The output jack: tip to OUT, sleeve to GND |
| J6 TRACK | two pins | The TRACK toggle, across the two pins |
| J7 MR | one pin | The divider's reset. Leave it open, or wire it to an octave pin |
| JP1 BYPASS | two pins | Short it only with the TL072 left out |
| GAIN | 1 / W / 3 | The GAIN pot, B100K. On wires: the pot's lug 1 to 1, its middle lug to W, and lug 3 to 3 |
| VOLUME | 1 / W / 3 | The VOLUME pot, B100K. On wires: the pot's lug 1 to 1, its middle lug to W, and lug 3 to 3 |
| HUM TEMPO, HUM PITCH | 1 / W / 3 | Hum's two pots, 100K. On wires: the pot's lug 1 to 1, its middle lug to W, and lug 3 to 3 |
| CHEW TEMPO, CHEW WIDTH | 1 / W / 3 | Chew's two pots, B500K. On wires: the pot's lug 1 to 1, its middle lug to W, and lug 3 to 3 |
| HUM LED | - / + | Hum's indicator LED: its short leg to - and its long leg to + |
Building it
- Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
- Before any chip goes in, power it up once. Fit the DC jack and the power toggle on their header, switch on, and put the meter's black probe on a GND pin and the red one in U1's pin 14 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there, or the full supply with the leads reversed, means look at the diode's band before going on. Switch off.
- The chips (U1, U2, U3, U4, U5, U6), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
- The electrolytics, long leg in the square pad, marked +, then the LEDs and the photocells. LED1 and LDR2 are the vactrol, side by side: seal them together in heat-shrink once both are soldered.
- The pots, on wires. Each pot has a header of its own, marked 1, W and 3. Fit the pot to the face first, then run three wires: lug 1 to 1, the middle lug to W, lug 3 to 3. The board sits in the box on its four M3 holes, on standoffs, screwed or stick-on.
- The headers. Wire them to the jacks and switches in the table above.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
Nobody has drilled this one yet, and how far the board sits behind the face is not measured: your standoffs set it. Offer the sheet up to your own box, board and parts before you make a hole.
The circuit and every part value are the Grubworks PCB's, the v1.0 board. Board by Onion Madder.