« Back to the PCBs

Grubworks PCB

CD4024 + TL072 + 4× NE555 on an 86 by 100 mm printed board · By Onion Madder · Mess O' Pedals

Grubworks on a printed board. Two voices, hum (an Opto Duet) and chew (an Atari Punk Console), clock a Grub Divider through a TL072 preamp, so the octave toggles pick which of seven divisions of the voices you hear. Six pots on the board: GAIN, VOLUME, and TEMPO and PITCH or WIDTH for each voice.

The built Grubworks board on a dark gray desk mat, not boxed, seen from the header edge so its print reads upside down. Six pots fill the far half of the purple board in two rows of three, the rows so close that each far pot's pin tab sits against the pot in front of it. The near half is fully populated: an upright 14-pin chip at the right, five 8-pin chips in two columns, resistors standing on end, small yellow dipped capacitors and black electrolytic cans, and at the center a clear LED beside a photocell. The pads marked LED2 are empty. Along the near edge, black and orange wires leave the power header, blue and orange the voice header, white and black the output, green and black the input header, and a bundle of blue wires the octave header.
Mine, built and working, November 2026, still on the bench and not yet boxed.
The Grubworks board itself, bare, photographed from the back and cut out from its background: a large purple board with gold pads and darker purple traces. The upper half is crowded with chip pads, small pads and traces under a row of header pads along the top edge, and six sets of three large round pot pads sit in two rows of three across the lower half. A white line drawing of a curled grub sits in the middle, and at the bottom center is a heart with a pulse line through it beside ONION MADDER, with GRUBWORKS underneath.
The board from the back, the side you solder on. Every part's number is printed on the front, beside its outline.

What you'll need

tap to expand / collapse

64 parts on the board. The numbers in brackets are the ones printed beside each part's outline. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 1× CD4024 (U1) - spot it: CD4024 printed on top, a notch or dot marks pin 1. The divider
  • 1× TL072 (U2) - spot it: TL072 printed on top, a notch or dot marks pin 1. The preamp. Any dual op-amp with the standard pinout goes in the same holes
  • 2× NE555 (U3, U4) - spot it: NE555 printed on top, a notch or dot marks pin 1. Hum: U3 is the engine, U4 the voice
  • 2× NE555 (U5, U6) - spot it: NE555 printed on top, a notch or dot marks pin 1. Chew: U5 runs free and sets the pitch, U6 fires on each of its ticks and sets the width
  • 1× 1M resistor (R1) - spot it: bands brown-black-green. Octave 1
  • 1× 470K resistor (R2) - spot it: bands yellow-violet-yellow. Octave 2
  • 1× 220K resistor (R3) - spot it: bands red-red-yellow. Octave 3
  • 1× 100K resistor (R4) - spot it: bands brown-black-yellow. Octave 4
  • 1× 47K resistor (R5) - spot it: bands yellow-violet-orange. Octave 5
  • 1× 22K resistor (R6) - spot it: bands red-red-orange. Octave 6
  • 1× 10K resistor (R7) - spot it: bands brown-black-orange. Octave 7. R1 to R7 are the weighted ladder, every value different: they are what make this a mixer and not a selector
  • 1× 1M resistor (R11) - spot it: bands brown-black-green. Holds the preamp's input at the half rail
  • 5× 100K resistor (R8, R9, R12, R14, R15) - spot it: bands brown-black-yellow. R8 and R9 are the clock and reset pull-downs, R12 the preamp's feedback, R14 and R15 the half rail
  • 2× 10K resistor (R22, R23) - spot it: bands brown-black-orange. The two that sum the voices
  • 1× 2.2K resistor (R25) - spot it: bands red-red-red. The power LED's resistor
  • 9× 1K resistor (R10, R13, R16, R18, R20, R21, R24, R26, R27) - spot it: bands brown-black-red. R10 on the output, R13 the floor under GAIN, R16 and R18 hum's timing chains, R20 and R21 the floors under hum's TEMPO and PITCH, R24 chew's tempo stop, R26 and R27 the floors under chew's pots
  • 2× 100R resistor (R17, R19) - spot it: bands brown-black-brown. Hum's two outputs, where they mix
  • 1× 2.2nF ceramic (C7) - spot it: printed 222. The tracking cap
  • 3× 10nF ceramic (C9, C12, C17) - spot it: printed 103. C9 and C12 on hum's pin 5s, C17 chew's timing cap
  • 7× 100nF ceramic (C1, C6, C11, C15, C16, C18, C20) - spot it: printed 104. C11 is hum's voice timing cap and C18 chew's width timing cap; the rest sit across the supplies
  • 1× 100nF film or other non-polarized cap (C3) - spot it: a small box, printed 104. The input cap, a film one
  • 5× 10 µF electrolytic (C2, C4, C5, C8, C19) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. C8 is hum's engine timing cap; C2 and C19 output caps; C4 in the gain leg; C5 holds the half rail still
  • 4× 100 µF electrolytic (C10, C13, C14, C21) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. Hum's two output caps, and two across the supplies
  • 1× 1N5817 (D1) - spot it: black body, gray band. The band goes to the square pad, the end the board marks with a band and a K. Reverse-polarity protection; every stage takes its supply through it
  • 1× LED (LED1) - The vactrol's LED, beside LDR2. It runs bare, no resistor, as on the Opto Duet. The short leg, on the flat side of the rim, goes in the square pad
  • 1× LED (LED2) - Hum's indicator. The short leg, on the flat side of the rim, goes in the square pad
  • 1× photocell, an LDR (LDR2) - The vactrol's cell, beside LED1. Either way around
  • 1× B100K pot, 16 mm, board mount (RV1) - GAIN. Spot it: the B is the linear taper.
  • 1× B100K pot, 16 mm, board mount (RV2) - VOLUME. Spot it: the B is the linear taper.
  • 1× 100K pot, 16 mm, board mount (RV3) - HUM TEMPO.
  • 1× 100K pot, 16 mm, board mount (RV4) - HUM PITCH.
  • 1× B500K pot, 16 mm, board mount (RV5) - CHEW TEMPO. Spot it: the B is the linear taper.
  • 1× B500K pot, 16 mm, board mount (RV6) - CHEW WIDTH. Spot it: the B is the linear taper.
  • 1× Grubworks PCB

Off the board

  • 1× DC jack and a 9V supply, center negative. The Opto Duet wants 6V and up, or its LED stops flashing
  • 1× SPST toggle for power, between the DC jack's + lug and SW
  • 2× SPST toggles, hum on and chew on
  • 7× SPST toggles, one per octave
  • 1× SPST toggle for TRACK
  • 2× 3.5 mm jacks: the output, and EXT IN, which must be a switched jack, one with a third lug that touches the tip with nothing plugged in
  • 1× LED for power
  • Hookup wire for the headers

Before you solder

  • The pots and their 1K floors are on the board, and so is the vactrol, LED1 and LDR2, side by side, to be sealed together in heat-shrink once they are soldered.
  • JP1 bypasses the preamp. Leave the TL072 out and short JP1, and the voices go to the divider's clock with no gain stage. Decide before you solder the chip in.

The headers

Everything that leaves the board leaves from a header along the top edge, and each one has its pins labeled on the board.

HeaderPinsGoes to
J1DC+ / SW / GNDPower, wired the usual way: the DC jack's + lug to one lug of the power toggle, the toggle's other lug to SW, and the jack's - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. SW is the board's power input, through D1, which guards against a supply plugged in the wrong way around. DC+ connects to nothing on the board: it is a spare pad to join the jack's + and the toggle on, if that is easier, and it can stay empty. The note printed on the board, power toggle between DC+ and SW, means the same thing
J2HUM / + / CHEWThe two voice toggles. Each one's middle lug to +, and its other lug to HUM or CHEW
J31 to 7 / BUSThe octave toggles, one from each numbered pin to BUS. The printed numbers sit closer together than the holes, so count holes rather than reading the print: the square hole at the left end is 1, the next six are 2 to 7, and the eighth, at the right end, is BUS
J5TIP / SW / GNDEXT IN, a switched jack: tip to TIP, the switched lug to SW, sleeve to GND. Unplugged, the preamp hears both voices; a plug overrides them
J4OUT / GNDThe output jack: tip to OUT, sleeve to GND
J6TRACKThe TRACK toggle, across the two pins
J8LED+ / -The power LED, its long leg to LED+. Its resistor, R25, is on the board
J7MRThe divider's reset. Leave it open, or wire it to an octave pin
JP1BYPASSShort it only with the TL072 left out

Building it

  1. Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
  2. Before any chip goes in, power it up once. Fit the DC jack and the power toggle on their header, switch on, and put the meter's black probe on a GND pin and the red one in U1's pin 14 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there, or the full supply with the leads reversed, means look at the diode's band before going on. Switch off.
  3. The chips (U1, U2, U3, U4, U5, U6), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
  4. The electrolytics, long leg in the square pad, marked +, then the LEDs and photocells. The ones with a hole in the face (LED2) stand on their full legs, so their tops reach about 12 mm up to that hole: tack one leg, offer the board up to the drilled face, set the height, then solder the rest.
  5. The pots last. Push each one flush to the board and keep its shaft square before you solder the first leg; a crooked pot is a hole that will not line up.
  6. Or the pots on wires. The board is drawn for 16 mm board-mount pots, but depending on the pots you have, they may not sit right on it: different legs, a different body, or a shaft that will not reach the face. Then put them on short wires, one from each pad to the lug in the same place, so the knob still turns the right way. Off the pots, the board no longer hangs on them, so it needs another way to sit in the box, and the pot holes are yours to place.
  7. Into the box, board first. Solder a wire to every header pin you use, long enough to reach its wall, and put the board in on its pots before anything goes on the walls: the wall parts pass behind the board, so they go in after it. Then fit them and wire them up as the table above says.
Don't eyeball the holes. There is a 1:1 drilling template for the 1590BB, lying flat: the face, with the top, bottom, left and right walls unfolded beside it. The pot holes and the LED holes are where the board puts them, read off the board's own files, and the dashed outline shows where the board hangs behind the face.
The board hangs about 12 mm behind the face on its pot bodies, so anything on it taller than that, usually an electrolytic, gets laid over flat before the board goes in.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
Nobody has drilled this one yet. Fit the pots to the board, offer the board up to the sheet, and check it against your own parts before you make a hole.

Board by Onion Madder.