« Back to the PCBs

UNVERIFIED - THIS BOARD. The circuit is built and working: it is my Spider Sequencer PCB, the v1.0 board. This is its v1.1 redraw. These boards are made and here, but nobody has built one yet. Build one, fix whatever fights back, and this banner comes off.

Spider Sequencer PCB v1.1

CD4017 + NE555 on an 82 by 58 mm printed board, marked SPIDER SEQUENCER v1.1 · By Onion Madder · Mess O' Pedals

The Spider Sequencer on its v1.1 board. A 555 clocks a CD4017 through eight steps, each step has its own knob and its own LED, and the eight knobs share one CV output through a diode each. On this board all nine pots and all eight LEDs go on the face on wires, each from a header of its own.

The front of the Spider Sequencer v1.1 board, bare, cut out from its background: a wide purple board with white printing and gold pads. Along the top edge are the RATE B1M pot header and headers J5, J3, J2 and J1, with the diode D9 1N5817 at the right. Below them an 8-pin outline marked U2 NE555 and a 16-pin outline marked U1 CD4017 sit side by side, and the name SPIDER SEQUENCER v1.1 runs across the middle. The lower half is two rows of four steps: each a diode outline marked 1N4148 above a three-pin header marked STEP and B100K and a two-pin header marked LED.
The front, where the parts go. Every part's number is printed on it, and its value.
The back of the Spider Sequencer v1.1 board: purple solder mask with gold pads and the darker purple lines of the copper traces. A white line drawing of a spider sits at the left, and near the middle a heart with a pulse line through it beside ONION MADDER, with SPIDER SEQUENCER underneath.
The back, the side you solder on.

What you'll need

tap to expand / collapse

21 parts on the board. The numbers in brackets are the ones printed on the board, and so is each part's value. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 1× CD4017 (U1) - spot it: CD4017 printed on top, a notch or dot marks pin 1. The counter. The 16-pin one, not a 4022
  • 1× NE555 (U2) - spot it: NE555 printed on top, a notch or dot marks pin 1. The clock
  • 2× 10K resistor (R1, R2) - spot it: bands brown-black-orange. The clock's upper timing resistor and the RATE pot's floor
  • 1× 1K resistor (R3) - spot it: bands brown-black-red. On the clock output
  • 1× 100K resistor (R4) - spot it: bands brown-black-yellow. Holds the CV bus down
  • 1× 2.2K resistor (R5) - spot it: bands red-red-red. The one resistor all eight LEDs share
  • 2× 100nF ceramic (C2, C4) - spot it: printed 104. One on the 555's control pin, one across the supply
  • 1× 2.2 µF electrolytic (C1) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The clock's timing cap. A 1 µF runs twice as fast, a 4.7 half as fast
  • 1× 100 µF electrolytic (C3) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. Across the supply
  • 8× 1N4148 (D1, D2, D3, D4, D5, D6, D7, D8) - spot it: tiny glass body, black band. The band goes to the square pad, the end the board marks with a band and a K. One per step, each step's knob onto the CV bus
  • 1× 1N5817 (D9) - spot it: black body, gray band. The band goes to the square pad, the end the board marks with a band and a K. Reverse-polarity protection on the supply
  • 1× 2.2K resistor (R6) - spot it: bands red-red-red. The power light's resistor
  • 1× Spider Sequencer PCB v1.1

Off the board

  • 1× DC jack and a 9V supply, center negative
  • 1× SPST toggle for power, between the DC jack's + lug and SW
  • 8× B100K pots, the steps, on wires to STEP 1 to STEP 8
  • 1× B1M pot, RATE, on wires to its header
  • 8× LEDs, one per step, on wires to LED 1 to LED 8. All one color: they share one resistor, so mixed colors wander in brightness
  • 1× LED for power, on J6, if you want one
  • 2× 3.5 mm mono jacks, CV out and clock out
  • Optional: an on-on toggle (SPDT, no center-off) on J5 for eight or four steps. Cut SJ1 on the board first
  • Hookup wire

What changed from v1.0

  • The pots are off the board. On v1.0 nine 16 mm pots soldered to the board, packed so close they were hard to solder. Each is now a three-pin header marked 1, W and 3, and the pot goes on the face on wires.
  • So are the eight step LEDs, each on a two-pin header marked - and +. Nothing on the face is fixed by the board any more, so the layout of the face is yours.
  • RESET is tied on the board. SJ1, a solder jumper by the 4017, comes closed and joins RST to Q8, so the sequencer runs eight steps with nothing on J5 and RESET can never float. On v1.0 a link on J5 did that job, and without it the sequence stuck on step 1.
  • For an eight or four step switch, cut SJ1 first, then wire an on-on toggle to J5: common to RST, the two throws to Q8 and S5. Never a center-off toggle, and never cut SJ1 without fitting the toggle.
  • J2 reads CV, GND, signal first like every other jack header. On v1.0 it was GND, CV.
  • The resistors lie flat, and the board is smaller: 82 by 58 mm, from 74 by 82.
  • A power light header, J6. Its resistor, R6, 2.2K, is on the board.
  • The ceramic caps' holes are 5.08 mm apart, not 2.5, so a dipped ceramic drops in flat with no leg to kink.
  • Every value is printed on the board, on the part's outline or beside it, with its number.
  • Four M3 mounting holes, since the pots no longer hold the board.

The headers

Everything that leaves the board leaves from a header, and each one has its pins labeled on the board. The square pad is pin 1, the first one named here.

HeaderPinsGoes to
J1DC+ / SW / GNDPower, wired the usual way: the DC jack's + lug to one lug of the power toggle, the toggle's other lug to SW, and the jack's - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. SW is the board's power input, through D9, which guards against a supply plugged in the wrong way around. DC+ connects to nothing on the board: it is a spare pad to join the jack's + and the toggle on, if that is easier, and it can stay empty
J6LED+ / -The power light, if you want one: the LED's long leg to LED+ and its short leg to -. Its resistor, R6, 2.2K, is on the board. It lights when the power toggle is on
J2CV / GNDThe CV output jack: tip to CV, sleeve to GND
J3CLK / GNDThe clock output jack: tip to CLK, sleeve to GND
J5RST / Q8 / S5The step count, only if you want a switch. Leave it empty for eight steps. For eight or four, cut SJ1 and fit an on-on toggle: common to RST, throws to Q8 and S5
SJ1RST-Q8A solder jumper, closed as the board comes: it ties RST to Q8 for eight steps. Cut it only to use J5's toggle
RATE1 / W / 3The RATE pot, B1M. On wires: the pot's lug 1 to 1, its middle lug to W, and lug 3 to 3
STEP 1 to STEP 81 / W / 3The eight step pots, B100K. On wires: the pot's lug 1 to 1, its middle lug to W, and lug 3 to 3. If a knob runs backwards, swap its 1 and 3 wires
LED 1 to LED 8- / +The eight step LEDs: each one's short leg to - and its long leg to +

Building it

  1. Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
  2. Before any chip goes in, power it up once. Fit the DC jack and the power toggle on their header, switch on, and put the meter's black probe on a GND pin and the red one in U1's pin 16 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there, or the full supply with the leads reversed, means look at the diode's band before going on. Switch off.
  3. The chips (U1, U2), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
  4. The electrolytics, long leg in the square pad, marked +.
  5. The pots, on wires. Each pot has a header of its own, marked 1, W and 3. Fit the pot to the face first, then run three wires: lug 1 to 1, the middle lug to W, lug 3 to 3. The board sits in the box on its four M3 holes, on standoffs, screwed or stick-on.
  6. The headers. Wire them to the jacks and switches in the table above.
Don't eyeball the holes. There is a 1:1 drilling template for the 1590BB, lying flat: the face, with the left and right walls unfolded beside it. Every pot and LED on this board is on wires, so the board is not on the sheet: the sheet is the panel, and the board rides behind it. It is the v1.0 board's face, so the nine pots are 18 mm apart.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
Nobody has drilled this one yet, and how far the board sits behind the face is not measured: your standoffs set it. Offer the sheet up to your own box, board and parts before you make a hole.

The circuit and every part value are the Spider Sequencer PCB's, the v1.0 board. Board by Onion Madder.