« Back to the PCBs

Opto Duet CV PCB

2× NE555 on a 56 by 62 mm printed board · By Onion Madder · Mess O' Pedals

The Opto Duet CV on a printed board. Two 555s chained by light: one sets the tempo, the other makes the tone, and a sealed LED and photocell pair lets the first play the second. The board adds what the stripboard left off it: TEMPO, LEVEL and PITCH pots soldered straight to the board, a line output in place of the speaker, and a CV input on the pitch.

The built Opto Duet CV board on a dark gray desk mat, not boxed. The purple board is fully populated: two 8-pin chips side by side, beige and blue resistors, small yellow ceramic capacitors and four silver electrolytic cans. Between the chips a clear LED stands beside a photocell, the vactrol not yet sealed. Lower down, two more photocells stand on their legs at left and right with a lit LED between them, and three pots stamped B100K are soldered along the bottom edge, labeled TEMPO, LEVEL and PITCH on the board. An orange and a black wire leave the power header at the top left, its DC+ pad empty, and a white and a black wire run from the OUT header to a large panel jack at the top right. The CV header has no wires.
Mine, built and working, November 2026, still on the bench. I tested it with a B100K on LEVEL and a quarter-inch output jack, because the jack was what I had; the parts list's 3.5 mm jack is the plan. The CV input is not wired yet.
The Opto Duet CV board itself, bare, photographed from the back and cut out from its background: purple solder mask with gold pads and the darker purple lines of the copper traces. Header pads run along the top edge, the pads for two 8-pin chips and the parts around them fill the middle, and three sets of three large round pads for the pots run across near the bottom. At the bottom left are two white line drawings of winged bugs with antennae, and at the bottom right a heart with a pulse line through it beside the words ONION MADDER, with OPTO DUET CV underneath.
The board from the back, the side you solder on. Every part's number is printed on the front, beside its outline.

What you'll need

tap to expand / collapse

26 parts on the board. The numbers in brackets are the ones printed beside each part's outline. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 2× NE555 (U1, U2) - spot it: NE555 printed on top, a notch or dot marks pin 1. U1 is the engine, the slow one with the tempo; U2 is the voice
  • 1× 22K resistor (R5) - spot it: bands red-red-orange. The two voices into the LEVEL pot
  • 1× 4.7K resistor (R6) - spot it: bands yellow-violet-red. The pitch CV into U2's pin 5
  • 2× 1K resistor (R1, R3) - spot it: bands brown-black-red. One per timing chain, in series with the TEMPO and PITCH pots
  • 2× 100R resistor (R2, R4) - spot it: bands brown-black-brown. The two outputs, where they mix
  • 2× 10nF ceramic (C2, C5) - spot it: printed 103. On each 555's pin 5
  • 3× 100nF ceramic (C4, C8, C9) - spot it: printed 104. C4 is the voice's timing cap; C8 and C9 sit across the supply beside each 555
  • 1× 10 µF electrolytic (C1) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The engine's timing cap, the part that turns a scream into a tick
  • 3× 100 µF electrolytic (C3, C6, C7) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. Two output caps and one across the supply
  • 1× 1N5817 (D1) - spot it: black body, gray band. The band goes to the square pad, the end the board marks with a band and a K. Reverse-polarity protection on the supply
  • 1× LED (D2) - The vactrol's LED, beside LDR2. The short leg, on the flat side of the rim, goes in the square pad
  • 1× LED (D3) - On the voice's output, so it lights when the voice sounds. The short leg, on the flat side of the rim, goes in the square pad
  • 1× photocell, an LDR (LDR1) - The tempo eye, above TEMPO. Either way around
  • 1× photocell, an LDR (LDR2) - The vactrol's cell, beside D2. Either way around
  • 1× photocell, an LDR (LDR3) - The pitch eye, above PITCH. Either way around
  • 1× B100K pot, 16 mm, board mount (RV1) - TEMPO. Spot it: the B is the linear taper.
  • 1× B100K pot, 16 mm, board mount (RV2) - LEVEL. Spot it: the B is the linear taper.
  • 1× B100K pot, 16 mm, board mount (RV3) - PITCH. Spot it: the B is the linear taper.
  • 1× Opto Duet CV PCB

Off the board

  • 1× DC jack and a 9V supply, center negative
  • 1× SPST toggle for power, between the DC jack's + lug and SW
  • 1× 3.5 mm mono jack for the output
  • 1× 3.5 mm mono jack for the pitch CV
  • Heat-shrink for the vactrol, to seal D2 and LDR2 face to face
  • Hookup wire for the headers

What is different from the stripboard

  • A line output, not a speaker. The two voices mix through R5 into the LEVEL pot, and the pot's wiper goes to the OUT header. Plug it into an amp.
  • TEMPO and PITCH pots. Each sits in series with its 1K, between the 1K and pin 7, so the knob sets where the eye starts from and the eye still moves it.
  • One CV input, on the pitch. R6, 4.7K, takes the CV jack's tip into the voice's pin 5. The stripboard's tempo CV jack and its 4.7K are not on this board.
  • The eyes are on the board. LDR1 is the tempo eye and LDR3 the pitch eye, each just above its pot. LDR2 and D2 are the vactrol, side by side, so they get sealed together in heat-shrink once they are soldered.

The headers

Everything that leaves the board leaves from a header along the top edge, and each one has its pins labeled on the board.

HeaderPinsGoes to
J1DC+ / SW / GNDPower, wired the usual way: the DC jack's + lug to one lug of the power toggle, the toggle's other lug to SW, and the jack's - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. SW is the board's power input, through D1, which guards against a supply plugged in the wrong way around. DC+ connects to nothing on the board: it is a spare pad to join the jack's + and the toggle on, if that is easier, and it can stay empty. The note printed on the board, power toggle between DC+ and SW, means the same thing
J2OUT / GNDThe output jack: tip to OUT, sleeve to GND
J3CV / GNDThe pitch CV jack: tip to CV, sleeve to GND

Building it

  1. Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
  2. Before any chip goes in, power it up once. Fit the DC jack and the power toggle on their header, switch on, and put the meter's black probe on a GND pin and the red one in U1's pin 8 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there, or the full supply with the leads reversed, means look at the diode's band before going on. Switch off.
  3. The chips (U1, U2), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
  4. The electrolytics, long leg in the square pad, marked +, then the LEDs and photocells. The ones with a hole in the face (D3, LDR1, LDR3) stand on their full legs, so their tops reach about 12 mm up to that hole: tack one leg, offer the board up to the drilled face, set the height, then solder the rest.
  5. The pots last. Push each one flush to the board and keep its shaft square before you solder the first leg; a crooked pot is a hole that will not line up.
  6. Or the pots on wires. The board is drawn for 16 mm board-mount pots, but depending on the pots you have, they may not sit right on it: different legs, a different body, or a shaft that will not reach the face. Then put them on short wires, one from each pad to the lug in the same place, so the knob still turns the right way. Off the pots, the board no longer hangs on them, so it needs another way to sit in the box, and the pot holes are yours to place.
  7. Into the box, board first. Solder a wire to every header pin you use, long enough to reach its wall, and put the board in on its pots before anything goes on the walls: the wall parts pass behind the board, so they go in after it. Then fit them and wire them up as the table above says.
Don't eyeball the holes. There is a 1:1 drilling template for the 125B, standing on end: the face, with the top wall unfolded beside it. The eye and LED holes are where the board puts them, read off the board's own files; the pot holes sit 5 mm further from the eye and LED row than the files put them, which is where they fit. The dashed outline shows where the board hangs behind the face.
The board hangs about 12 mm behind the face on its pot bodies, so anything on it taller than that, usually an electrolytic, gets laid over flat before the board goes in.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
I drilled my box from this sheet, and it works. Still fit the pots to the board and offer it up to the sheet before you make a hole, in case your parts differ from mine.

Circuit from the Opto Duet CV stripboard guide, every part value taken from its layout file. Board by Onion Madder.