« Back to the PCBs

UNVERIFIED - THIS BOARD. The circuit is built and working: it is my Paper Mosquito Mk II, part for part and value for value. These boards are made and here, but nobody has built one yet. Build one, fix whatever fights back, and this banner comes off.

Mosquito Mk II PCB

2× NE555 on a 56 by 70 mm printed board, marked MOSQUITO MK II v1.1 · By Onion Madder · Mess O' Pedals

The Mosquito Mk II on a printed board: the Atari Punk Console on two 555s. One 555 runs free and PITCH sets how fast; the other fires once on each of its ticks, and SHAPE sets for how long. Everything but the two jacks is on the board: three pots, the power toggle and the power light.

The front of the Mosquito Mk II board, bare, cut out from its background: purple with white printing and gold pads. J1, labeled DC+ and GND, is in the top left corner and J2, OUT and GND, in the top right. Under them are the diode D1 1N5817, a row of resistors and small capacitors, and two 8-pin chip outlines marked U1 NE555 and U2 NE555. Below the chips are a wide outline marked SW1 POWER at the left and LED1 at the right, the name MOSQUITO MK II v1.1, and three square pot outlines along the bottom marked PITCH B500K, SHAPE B500K and VOL B10K.
The front, where the parts go. Every part's number is printed on it, and its value.
The back of the Mosquito Mk II board: purple solder mask with gold pads and the darker purple lines of the copper traces. A white line drawing of a mosquito sits in the middle, and at the bottom a heart with a pulse line through it beside ONION MADDER, with MOSQUITO MK II underneath.
The back, the side you solder on.

What you'll need

tap to expand / collapse

15 parts on the board. The numbers in brackets are the ones printed on the board, and so is each part's value. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 2× NE555 (U1, U2) - spot it: NE555 printed on top, a notch or dot marks pin 1. U1 runs free and sets the pitch; U2 fires on each of its ticks and sets the shape
  • 2× 1K resistor (R1, R2) - spot it: bands brown-black-red. One per 555, in series with its pot between the supply and the timing cap
  • 1× 2.2K resistor (R3) - spot it: bands red-red-red. The power light's resistor
  • 2× 10nF ceramic (C1, C2) - spot it: printed 103. The two timing caps, C1 for pitch and C2 for shape
  • 1× 100nF ceramic (C4) - spot it: printed 104. Across the supply
  • 1× 10 µF electrolytic (C3) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The output cap
  • 1× 1N5817 (D1) - spot it: black body, gray band. The band goes to the square pad, the end the board marks with a band and a K. Reverse-polarity protection on the supply
  • 1× LED (LED1) - The power light, 3 mm, any color. The short leg, on the flat side of the rim, goes in the square pad
  • 1× mini toggle switch, SPDT, PCB mount (SW1) - The power toggle. A mini toggle with PCB pins, three in a row; the middle and one outer pin do the work
  • 2× B500K pot, 9 mm, a Bourns PTV09A-4020F-B504 (RV1, RV2) - PITCH and SHAPE. Spot it: the B is the linear taper.
  • 1× B10K pot, 9 mm, a Bourns PTV09A-4020F-B103 (RV3) - VOL. Spot it: the B is the linear taper.
  • 1× Mosquito Mk II PCB

Off the board

  • 1× DC jack and a 9V supply, center negative, or a 9V battery and snap: + to DC+, - to GND
  • 1× 3.5 mm mono jack for the output
  • Hookup wire

What is different from the paper one

  • The pots are on the board, three 9 mm Bourns PTV09A-4s: PITCH, SHAPE and VOL. On paper they hang off on wires.
  • So are the power toggle and the power light. SW1 is a PCB-mount mini toggle and LED1 a 3 mm LED, both soldered straight in.
  • Only two things leave the board: power in on J1 and the output on J2.
  • Everything else is the paper circuit, the same numbers on the same parts, R1 to R3, C1 to C4, D1 and the two chips.

The headers

Everything that leaves the board leaves from a header, and each one has its pins labeled on the board. The square pad is pin 1, the first one named here.

HeaderPinsGoes to
J1DC+ / GNDPower in: the DC jack's + lug to DC+ and its - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. The board's own toggle, SW1, switches it, and D1 guards against a supply plugged in the wrong way around
J2OUT / GNDThe output jack: tip to OUT, sleeve to GND

Building it

  1. Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
  2. Before any chip goes in, power it up once. Fit the power toggle, SW1, and wire the DC jack to J1. Switch on, and put the meter's black probe on a GND pin and the red one in U1's pin 8 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there with the toggle either way means look at the diode's band before going on. Switch off.
  3. The chips (U1, U2), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
  4. The electrolytics, long leg in the square pad, marked +, then the LEDs. LED1 looks out through the face, so leave its legs long: tack one leg, offer the board up to your drilled face, set the height, then solder the other.
  5. The pots last. Each one's three legs go in the three round holes and its two side tabs in the two slots. Seat it flat on the board with its shaft square, then solder the legs and both tabs; a crooked pot is a hole that will not line up.
  6. Fixing it in the box. These pots have no nut, so they do not hold the board to the face. The four holes in the board are for M3 standoffs: screwed through the face, or the stick-on kind.
  7. The headers. Wire them to the jacks and switches in the table above.
Don't eyeball the holes. There is a 1:1 drilling template for the 125B, standing on end: the face, with the top wall unfolded beside it. The pot, toggle and LED holes are where the board puts them, read off the board's own files, and the dashed outline shows where the board sits behind the face.
The board's four M3 holes are on the sheet as small dashed circles. They are optional: screws through the face into standoffs, or stick-on standoffs and no holes at all.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
Nobody has drilled this one yet, and how far the board sits behind the face is not measured: your standoffs set it. Offer the sheet up to your own box, board and parts before you make a hole.

Circuit from my Paper Mosquito Mk II, the Atari Punk Console on two 555s. Board by Onion Madder.