« Back to the PCBs

UNVERIFIED - THIS BOARD. The circuit is built and working: it is my Cicada NAND PCB, the v1.0 board. This is its v1.1 redraw. These boards are made and here, but nobody has built one yet. Build one, fix whatever fights back, and this banner comes off.

Cicada NAND PCB v1.1

CD4093 on a 56 by 78 mm printed board, marked CICADA NAND v1.1 · By Onion Madder · Mess O' Pedals

The Cicada NAND on its v1.1 board. Four voices from one CD4093, each a Schmitt NAND gate with its own timing cap a decade apart from its neighbors, its own PITCH pot on the board and its own gate on a header, all mixed to one output.

The front of the Cicada NAND v1.1 board, bare, cut out from its background: a tall purple board with white printing and gold pads. Headers J1, J3 and J2 run along the top edge, labeled DC+, SW, GND, EN1 to EN4 and OUT. Below them are the diode D1 1N5817, rows of resistors lying flat and four box capacitor outlines marked 1u. A 14-pin chip outline marked U1 CD4093 lies across the middle above the name CICADA NAND v1.1, and four square pot outlines stand two down each side of the lower half, marked PITCH 1 B1M to PITCH 4 B1M, with more resistors between them.
The front, where the parts go. Every part's number is printed on it, and its value.
The back of the Cicada NAND v1.1 board: purple solder mask with gold pads and the darker purple lines of the copper traces. A white line drawing of a cicada seen from above sits at the lower right, and at the bottom a heart with a pulse line through it beside ONION MADDER, with CICADA NAND underneath.
The back, the side you solder on.

What you'll need

tap to expand / collapse

31 parts on the board. The numbers in brackets are the ones printed on the board, and so is each part's value. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 1× CD4093 (U1) - spot it: CD4093 printed on top, a notch or dot marks pin 1. Four Schmitt NAND gates, one per voice
  • 4× 1M resistor (R9, R10, R11, R12) - spot it: bands brown-black-green. The gate pull-ups. Each holds a voice on until something pulls it low
  • 1× 1M resistor (R13) - spot it: bands brown-black-green. The output pull-down
  • 4× 10K resistor (R5, R6, R7, R8) - spot it: bands brown-black-orange. The mixer, one per voice
  • 4× 1K resistor (R1, R2, R3, R4) - spot it: bands brown-black-red. One per pot, in series and not optional: at zero ohms the gate's output ties straight to its own input and the voice dies into a short
  • 1× 1nF ceramic (C3) - spot it: printed 102. Voice 3's timing cap
  • 1× 10nF ceramic (C1) - spot it: printed 103. Voice 1's timing cap
  • 1× 100nF ceramic (C2) - spot it: printed 104. Voice 2's timing cap
  • 1× 1 µF ceramic (C4) - spot it: printed 105. Voice 4's timing cap, the lowest
  • 1× 100nF ceramic (C9) - spot it: printed 104. Across the supply
  • 4× 1 µF film or other non-polarized cap (C5, C6, C7, C8) - spot it: a small box, printed 105. The mixer, one per voice. Non-polarized; the board has a box footprint for them
  • 1× 10 µF electrolytic (C10) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The output cap
  • 1× 100 µF electrolytic (C11) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. Across the supply
  • 1× 1N5817 (D1) - spot it: black body, gray band. The band goes to the square pad, the end the board marks with a band and a K. Reverse-polarity protection on the supply
  • 1× 2.2K resistor (R14) - spot it: bands red-red-red. The power light's resistor
  • 4× B1M pot, 9 mm, a Bourns PTV09A-4020F-B105 (RV1, RV2, RV3, RV4) - PITCH 1 to 4. Spot it: the B is the linear taper.
  • 1× Cicada NAND PCB v1.1

Off the board

  • 1× DC jack and a 9V supply, center negative
  • 1× SPST toggle for power, between the DC jack's + lug and SW
  • 1× LED for power, on J4, if you want one
  • 4× SPST toggles for the gates, if you want them. A touch plate or a photocell to GND works on the same pins
  • 1× 3.5 mm mono jack for the output
  • Hookup wire

What changed from v1.0

  • The resistors lie flat. On v1.0 all thirteen stood on end.
  • The pots are 9 mm Bourns PTV09A-4s (PITCH 1 to PITCH 4), still soldered to the board, in place of v1.0's 16 mm pots. PITCH 1 and 3 are down the left side and 2 and 4 down the right, with the chip between them.
  • A power light header, J4. Its resistor, R14, 2.2K, is on the board.
  • The ceramic caps' holes are 5.08 mm apart, not 2.5, so a dipped ceramic drops in flat with no leg to kink.
  • Every value is printed on the board, on the part's outline or beside it, with its number.
  • Four M3 mounting holes. These pots have no nut, so they do not hold the board to the face the way v1.0's did. The holes are for standoffs or screws.
  • The circuit is v1.0's, every part and value, R14 aside.

The headers

Everything that leaves the board leaves from a header, and each one has its pins labeled on the board. The square pad is pin 1, the first one named here.

HeaderPinsGoes to
J1DC+ / SW / GNDPower, wired the usual way: the DC jack's + lug to one lug of the power toggle, the toggle's other lug to SW, and the jack's - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. SW is the board's power input, through D1, which guards against a supply plugged in the wrong way around. DC+ connects to nothing on the board: it is a spare pad to join the jack's + and the toggle on, if that is easier, and it can stay empty
J3EN1 / EN2 / EN3 / EN4 / GNDThe gates, one per voice. A toggle from each EN pin to GND: closed is that voice off. Leave a pin bare and its voice just plays
J2OUT / GNDThe output jack: tip to OUT, sleeve to GND
J4LED+ / -The power light, if you want one: the LED's long leg to LED+ and its short leg to -. Its resistor, R14, 2.2K, is on the board. It lights when the power toggle is on

Building it

  1. Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
  2. Before any chip goes in, power it up once. Fit the DC jack and the power toggle on their header, switch on, and put the meter's black probe on a GND pin and the red one in U1's pin 14 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there, or the full supply with the leads reversed, means look at the diode's band before going on. Switch off.
  3. The chips (U1), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
  4. The electrolytics, long leg in the square pad, marked +.
  5. The pots last. Each one's three legs go in the three round holes and its two side tabs in the two slots. Seat it flat on the board with its shaft square, then solder the legs and both tabs; a crooked pot is a hole that will not line up.
  6. Fixing it in the box. These pots have no nut, so they do not hold the board to the face. The four holes in the board are for M3 standoffs: screwed through the face, or the stick-on kind.
  7. The headers. Wire them to the jacks and switches in the table above.
Don't eyeball the holes. There is a 1:1 drilling template for the 125B, standing on end: the face, with the top wall unfolded beside it. The pot holes are where the board puts them, read off the board's own files, and the dashed outline shows where the board sits behind the face.
The board's four M3 holes are on the sheet as small dashed circles. They are optional: screws through the face into standoffs, or stick-on standoffs and no holes at all.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
Nobody has drilled this one yet, and how far the board sits behind the face is not measured: your standoffs set it. Offer the sheet up to your own box, board and parts before you make a hole.

The circuit and every part value are the Cicada NAND PCB's, the v1.0 board. Board by Onion Madder.