« Back to the PCBs

UNVERIFIED - THIS BOARD. The circuit is built and working: it is my Power Starve on stripboard, part for part and value for value. These boards are made and here, but nobody has built one yet. Build one, fix whatever fights back, and this banner comes off.

Power Starve PCB

LM317 on a 21 by 22 mm printed board, marked POWER STARVE v1.0 · By Onion Madder · Mess O' Pedals

The Power Starve on a printed board the size of a postage stamp, 21 by 22 mm, to go inside the toy. An LM317 sits between the supply and the toy, and the pot only sets the regulator's reference, so the toy's current never runs through the pot's track. Eight parts on the board, and one row of eight labeled pads for everything that leaves it.

What you'll need

tap to expand / collapse

8 parts on the board. The numbers in brackets are the ones printed on the board. The board is too small to print the values as well, so go by this list. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 1× LM317 (U1) - spot it: LM317 printed on the black body. The regulator, a TO-220: three legs and a metal tab
  • 1× 220R resistor (R1) - spot it: bands red-red-brown. Sets the regulator's reference with the pot
  • 1× 1K resistor (R2) - spot it: bands brown-black-red. The LED's resistor
  • 1× 100nF ceramic (C1) - spot it: printed 104. On the supply, at the regulator's input
  • 2× 10 µF electrolytic (C2, C3) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. C2 steadies the adjust pin, C3 is on the output
  • 2× 1N5817 (D1, D2) - spot it: black body, gray band. They stand on end, and the lead from the band end goes to the square pad. D1 guards against a supply connected the wrong way around; D2 protects the regulator when the output sits above the input
  • 1× Power Starve PCB

Off the board

  • 1× B1K pot, linear, the starve knob
  • 1× SPDT toggle for bypass
  • 1× LED
  • The toy, and its own supply: the board goes between the two
  • Hookup wire

What is different from the stripboard

  • Nothing in the circuit. The same eight parts with the same numbers and values.
  • The resistors and diodes stand on end, to fit the board. Each one's body goes over the circle printed for it.
  • One row of eight pads along the bottom edge, in four labeled pairs: POT, LED, BYPASS and POWER.
  • No mounting holes. It is light enough to hang on its wires or sit under a dab of hot glue.

The headers

Everything that leaves the board leaves from the one row of eight pads along the bottom edge, labeled in pairs. Left to right:

HeaderPinsGoes to
POTW / GThe starve pot, B1K: its wiper to W and its lug 3 to G, with lug 1 jumpered to the wiper on the pot itself
LED+ / -The light: its long leg to + and its short leg to -. Its resistor, R2, is on the board, and it runs off the starved output, so it dims as you starve
BYPASSOUT / DIRThe bypass toggle, an SPDT: one throw to OUT, the starved supply, and the other to DIR, the supply straight through. The toggle's common goes to the toy's +
POWERIN / GNDThe supply: battery or DC jack + to IN and - to GND. The toy's - goes to GND too, and can share that pad

Building it

  1. R1 and R2 first, standing on end: the body over the printed circle, the bare leg folded over and down into the other hole. Then C1.
  2. The two diodes, D1 and D2, standing on end the same way. Each has a square pad and a round one: the end with the band is the one that goes to the square pad. Check each against the board before you solder, because the two face different ways.
  3. The regulator, U1, the LM317. Its three legs go in the row of three holes with the metal tab toward the edge of the board, over the narrow strip of its outline.
  4. The two electrolytics, C2 and C3, long leg in the square pad, marked +.
  5. The pads. Wire the pot, the LED, the bypass toggle and the supply as the table above says.
  6. Before the toy goes on, meter it. Power on IN and GND, black probe on GND, red on OUT: turning the pot should sweep the voltage, and it should never read more than the supply. Red on DIR should read the supply less about 0.2V for D1.

Circuit from the Power Starve stripboard guide. Board by Onion Madder.