« Back to the PCBs

UNVERIFIED - THIS BOARD. The circuit is the Cicada NAND Mk II on stripboard, value for value, which nobody has built yet either. Its four oscillators are the Cicada NAND's, and that one is built and working. These boards are made and here, but nobody has built one yet. Build one, fix whatever fights back, and this banner comes off.

Cicada NAND Mk II PCB

CD4093 + CD4070 on an 80 by 95 mm printed board, marked CICADA NAND MK II v1.0 · By Onion Madder · Mess O' Pedals

The Cicada NAND Mk II on a printed board. The Cicada's four voices on one CD4093, and a CD4070 that lets them work on each other: every voice has a gate that turns it off, lets it run, or hands it to a partner voice to chop, and an XOR switch that swaps it for the XOR of itself and that partner. Four PITCH pots, TONE and VOLUME are on the board, and each voice has one header for its jack and toggles.

The front of the Cicada NAND Mk II board, bare, cut out from its background: a large purple board with white printing and gold pads. Six headers run along the top edge: J1 POWER, J2 to J5 marked VOICE 1 to VOICE 4, and J6 OUT. Below a row of resistors, two 14-pin chip outlines marked U1 CD4093 and U2 CD4070 lie side by side, with more resistors, small capacitors and four box capacitor outlines under them and the name CICADA NAND MK II v1.0. The lower part holds six square pot outlines in two rows of three, marked PITCH 1 B1M, PITCH 2 B1M and TONE B100K above PITCH 3 B1M, PITCH 4 B1M and VOLUME A100K.
The front, where the parts go. Every part's number is printed on it, and its value.
The back of the Cicada NAND Mk II board: purple solder mask with gold pads and the darker purple lines of the copper traces. A white line drawing of a cicada seen from above sits at the lower left, and under it a heart with a pulse line through it beside ONION MADDER, with CICADA NAND MK II underneath.
The back, the side you solder on.

What you'll need

tap to expand / collapse

41 parts on the board. The numbers in brackets are the ones printed on the board, and so is each part's value. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 1× CD4093 (U1) - spot it: CD4093 printed on top, a notch or dot marks pin 1. Four Schmitt NAND gates, one per voice
  • 1× CD4070 (U2) - spot it: CD4070 printed on top, a notch or dot marks pin 1. Four XOR gates, one per voice
  • 4× 1M resistor (R9, R10, R11, R12) - spot it: bands brown-black-green. The gate pull-ups. Each holds a voice on until something pulls its gate low
  • 4× 100K resistor (R14, R15, R16, R17) - spot it: bands brown-black-yellow. Hold each XOR input low, so a voice passes straight through with its XOR toggle open
  • 4× 10K resistor (R5, R6, R7, R8) - spot it: bands brown-black-orange. The mixer, one per voice
  • 4× 10K resistor (R18, R19, R20, R21) - spot it: bands brown-black-orange. One between each gate and its chip pin
  • 1× 2.2K resistor (R13) - spot it: bands red-red-red. The power light's resistor
  • 4× 1K resistor (R1, R2, R3, R4) - spot it: bands brown-black-red. One per pitch pot, in series and not optional: at zero ohms the gate's output ties straight to its own input and the voice dies into a short
  • 1× 1nF ceramic (C3) - spot it: printed 102. Voice 3's timing cap, the highest
  • 1× 10nF ceramic (C1) - spot it: printed 103. Voice 1's timing cap
  • 1× 100nF ceramic (C2) - spot it: printed 104. Voice 2's timing cap
  • 1× 1 µF ceramic (C4) - spot it: printed 105. Voice 4's timing cap, the lowest
  • 2× 100nF ceramic (C9, C11) - spot it: printed 104. C9 across the supply, C11 the tone cap
  • 4× 1 µF film or other non-polarized cap (C5, C6, C7, C8) - spot it: a small box, printed 105. The mixer, one per voice. Non-polarized; the board has a box footprint for them
  • 1× 10 µF electrolytic (C10) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The output cap
  • 1× 1N5817 (D1) - spot it: black body, gray band. The band goes to the square pad, the end the board marks with a band and a K. Reverse-polarity protection on the supply
  • 4× B1M pot, 9 mm, a Bourns PTV09A-4020F-B105 (RV1, RV2, RV3, RV4) - PITCH 1 to 4. Spot it: the B is the linear taper.
  • 1× B100K pot, 9 mm, a Bourns PTV09A-4020F-B104 (RV5) - TONE. Spot it: the B is the linear taper.
  • 1× A100K pot, 9 mm, a Bourns PTV09A-4020F-A104 (RV6) - VOLUME. Spot it: the A is the log taper.
  • 1× Cicada NAND Mk II PCB

Off the board

  • 1× DC jack and a 9V supply, center negative
  • 1× SPST toggle for power, between the DC jack's + lug and SW
  • 1× LED for power, on J1's LED pad
  • 4× 3.5 mm switched mono jacks for the gates, ones with a third lug that touches the tip with nothing plugged in
  • 4× on-off-on toggles for the gates: one way is partner, the middle is free running, the other way is off
  • 4× SPST toggles for the XORs
  • 1× 3.5 mm mono jack for the output
  • Hookup wire

What is different from the stripboard

  • All six pots are on the board, 9 mm Bourns PTV09A-4s: PITCH 1 to 4, TONE and VOLUME. On stripboard they are on wires, on twenty-eight pads.
  • One header per voice. J2 to J5 each carry everything one voice's jack and two toggles need: its gate, a ground, its partner's output twice, and its XOR input.
  • The partner is already chosen on the board. Voice 1's header brings out voice 2's output, voice 2's brings out voice 4's, voice 3's brings out voice 1's and voice 4's brings out voice 3's, the pairing the stripboard guide wires by hand.
  • Everything else is the stripboard circuit, the same numbers on the same parts.
  • Read the header labels across two lines. They are staggered to fit. On a voice header the pads run G, GND, O, X, O.

The headers

Everything that leaves the board leaves from a header, and each one has its pins labeled on the board. The square pad is pin 1, the first one named here.

HeaderPinsGoes to
J1 POWERDC+ / SW / GND / LEDPower, wired the usual way: the DC jack's + lug to one lug of the power toggle, the toggle's other lug to SW, and the jack's - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. SW is the board's power input, through D1, which guards against a supply plugged in the wrong way around. DC+ connects to nothing on the board: it is a spare pad to join the jack's + and the toggle on, if that is easier, and it can stay empty. LED is the power light: the LED's long leg to LED and its short leg to GND. Its resistor is on the board
J2 to J5, VOICE 1 to VOICE 4G / GND / O / X / OOne voice each. G is the voice's gate: to its gate jack's tip. GND: the jack's sleeve, and the gate toggle's off lug. The first O, the partner's output: to the gate toggle's other outer lug. X and the second O: the XOR toggle, one lug to each. The gate toggle's middle lug goes to the jack's switched lug, so a plug takes over from the toggle. With nothing wired, the voice just plays
J6 OUTOUT / GNDThe output jack: tip to OUT, sleeve to GND. It is after the volume pot

Building it

  1. Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
  2. Before any chip goes in, power it up once. Fit the DC jack and the power toggle on their header, switch on, and put the meter's black probe on a GND pin and the red one in U1's pin 14 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there, or the full supply with the leads reversed, means look at the diode's band before going on. Switch off.
  3. The chips (U1, U2), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
  4. The electrolytics, long leg in the square pad, marked +.
  5. The pots last. Each one's three legs go in the three round holes and its two side tabs in the two slots. Seat it flat on the board with its shaft square, then solder the legs and both tabs; a crooked pot is a hole that will not line up.
  6. Fixing it in the box. These pots have no nut, so they do not hold the board to the face. The four holes in the board are for M3 standoffs: screwed through the face, or the stick-on kind.
  7. The headers. Wire them to the jacks and switches in the table above.
Don't eyeball the holes. There is a 1:1 drilling template for the 1590DD, on its back: the face, with the top wall unfolded beside it. The pot holes are where the board puts them, read off the board's own files, and the dashed outline shows where the board sits behind the face.
The board's four M3 holes are on the sheet as small dashed circles. They are optional: screws through the face into standoffs, or stick-on standoffs and no holes at all.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
Nobody has drilled this one yet, and how far the board sits behind the face is not measured: your standoffs set it. Offer the sheet up to your own box, board and parts before you make a hole.

Circuit from the Cicada NAND Mk II stripboard guide, every part value the same. Board by Onion Madder.