« Back to the PCBs

UNVERIFIED - THIS BOARD. The circuit is The Popo on stripboard, value for value: my built Siren and my built Police Lights on one board, which nobody has built as one board yet either. These boards are made and here, but nobody has built one yet. Build one, fix whatever fights back, and this banner comes off.

The Popo PCB

3× NE555 on a 74 by 52 mm printed board, marked THE POPO v1.0 · By Onion Madder · Mess O' Pedals

The Popo on a printed board: a cop-car siren with a woop button and a wail switch, and a red and blue wig-wag flashing over it. Three 555s, marked on the board by what they do: SIREN, WAIL and LIGHTS. The red and blue LEDs are on the board, and the pitch pot, the button, the switch and the jacks go on headers.

The front of The Popo board, bare, cut out from its background: a wide purple board with white printing and gold pads. Headers J1 POWER, J5 CV IN and J2 OUT are along the top edge. Three 8-pin chip outlines stand in a row across the middle, marked IC3 LIGHTS, IC2 WAIL and IC1 SIREN, with resistors lying flat between them and round capacitor outlines around them. The name THE POPO v1.0 is at the lower left, above two round LED outlines marked D2 RED and D3 BLUE, and the headers J3 WOOP, J4 WAIL and J6 PITCH run along the bottom edge.
The front, where the parts go. Every part's number is printed on it, and its value.
The back of The Popo board: purple solder mask with gold pads and the darker purple lines of the copper traces. At the right is a heart with a pulse line through it beside the words ONION MADDER.
The back, the side you solder on.

What you'll need

tap to expand / collapse

33 parts on the board. The numbers in brackets are the ones printed on the board, and so is each part's value. ↓ Download the parts list (PDF), one page to print for the bench and tick off as each part goes in.

  • 3× NE555 (IC1, IC2, IC3) - spot it: NE555 printed on top, a notch or dot marks pin 1. IC1 is the siren, IC2 the wail that sweeps it, IC3 flashes the lights
  • 4× 10K resistor (R1, R5, R8, R10) - spot it: bands brown-black-orange. R1, R8 and R10 are each 555's upper timing resistor; R5 is on the transistor's base
  • 2× 2.2K resistor (R2, R7) - spot it: bands red-red-red. R2 is the siren's lower timing resistor, R7 the transistor's emitter resistor
  • 1× 2.2K resistor (R15) - spot it: bands red-red-red. The power light's resistor
  • 2× 22K resistor (R6, R14) - spot it: bands red-red-orange. Into the transistor's base: R6 from the sweep cap, R14 from the CV jack
  • 2× 470R resistor (R12, R13) - spot it: bands yellow-violet-brown. One per light, red and blue
  • 1× 100K resistor (R11) - spot it: bands brown-black-yellow. The lights' timing resistor
  • 1× 220K resistor (R9) - spot it: bands red-red-yellow. The wail's timing resistor
  • 1× 1K resistor (R3) - spot it: bands brown-black-red. On the output
  • 1× 4.7K resistor (R4) - spot it: bands yellow-violet-red. Charges the woop and wail cap
  • 1× 1N4148 (D1) - spot it: tiny glass body, black band. The band goes to the square pad, the end the board's outline marks with a band. Between the wail 555 and its switch
  • 1× 1N5817 (D4) - spot it: black body, gray band. The band goes to the square pad, the end the board's outline marks with a band. Reverse-polarity protection on the supply
  • 1× 150nF ceramic (C1) - spot it: printed 154. The siren's timing cap
  • 3× 10nF ceramic (C2, C6, C9) - spot it: printed 103. One on each 555's pin 5
  • 1× 2N3904 transistor (Q1) - spot it: a small black half-round with three legs and 2N3904 printed on the flat. Bends the siren's pitch
  • 1× 2.2 µF electrolytic (C8) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The lights' timing cap
  • 1× 10 µF electrolytic (C3) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The output cap
  • 1× 22 µF electrolytic (C5) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The wail's timing cap
  • 1× 47 µF electrolytic (C4) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. The cap the woop and wail charge, the sweep itself
  • 2× 100 µF electrolytic (C7, C10) - spot it: a can with a stripe down the minus leg. The long leg goes in the square pad, marked +. Across the supply
  • 1× red LED (D2) - The red light, 5 mm. The short leg, on the flat side of the rim, goes in the square pad
  • 1× blue LED (D3) - The blue light, 5 mm. The short leg, on the flat side of the rim, goes in the square pad
  • 1× The Popo PCB

Off the board

  • 1× DC jack and a 9V supply, center negative
  • 1× SPST toggle for power, between the DC jack's + lug and SW
  • 1× LED for power, on J1's LED pad
  • 1× B100K pot, linear, the siren's pitch, on wires to J6
  • 1× momentary button, normally open, for the woop
  • 1× SPST toggle for the wail
  • 1× 3.5 mm mono jack for the output
  • 1× 3.5 mm mono jack for CV in, if you want it
  • Hookup wire

What is different from the stripboard

  • The CV input's 22K is on the board, R14. On stripboard it hangs off the board on the CV jack's wire.
  • The power light's resistor is on the board too, R15, 2.2K, with a pad for the LED on J1.
  • The red and blue LEDs solder to the board, D2 and D3, on legs long enough to reach the face.
  • The chips are IC1, IC2 and IC3, as on the stripboard, and each is printed with its job: IC1 SIREN, IC2 WAIL, IC3 LIGHTS.
  • Everything else is the stripboard circuit, the same numbers on the same parts.

The headers

Everything that leaves the board leaves from a header, and each one has its pins labeled on the board. The square pad is pin 1, the first one named here.

HeaderPinsGoes to
J1 POWERDC+ / SW / GND / LEDPower, wired the usual way: the DC jack's + lug to one lug of the power toggle, the toggle's other lug to SW, and the jack's - lug to GND. On a center-negative supply the + is the jack's sleeve lug and the - is its center pin. SW is the board's power input, through D4, which guards against a supply plugged in the wrong way around. DC+ connects to nothing on the board: it is a spare pad to join the jack's + and the toggle on, if that is easier, and it can stay empty. LED is the power light: the LED's long leg to LED and its short leg to GND. Its resistor is on the board
J5 CV INCV / GNDThe CV jack, for the siren's pitch: tip to CV, sleeve to GND. Its 22K, R14, is on the board
J2 OUTOUT / GNDThe output jack: tip to OUT, sleeve to GND
J3 WOOPtwo padsThe woop button, a normally open momentary: one lug to each pad
J4 WAILtwo padsThe wail toggle: one lug to each pad
J6 PITCH1 / W / 3The siren's pitch pot, B100K: lug 1 to 1, the middle lug to W, lug 3 to 3. If the knob runs backwards, swap the 1 and 3 wires at the pot

Building it

  1. Lowest parts first, so the board sits flat on the bench while you solder: resistors, then the diodes, then the small ceramic caps.
  2. Before any chip goes in, power it up once. Fit the DC jack and the power toggle on their header, switch on, and put the meter's black probe on a GND pin and the red one in IC1's pin 8 hole, from the top. You want the supply, less about 0.2V for the diode. Nothing there, or the full supply with the leads reversed, means look at the diode's band before going on. Switch off.
  3. The chips (IC1, IC2, IC3), soldered straight in. Pin 1 goes to the square pad, the end the board marks with a notch.
  4. The electrolytics, long leg in the square pad, marked +, then the transistor and the LEDs. The transistor, Q1, goes in with its flat side matching the flat of its outline. The red and blue LEDs, D2 and D3, look out through the face, so leave their legs long: tack one leg, offer the board up to your drilled face, set the height, then solder the other.
  5. Into the box. The board sits on its four M3 holes, on standoffs, screwed or stick-on. The pitch pot goes on the face, on three wires to its header.
  6. The headers. Wire them to the jacks and switches in the table above.
Don't eyeball the holes. There is a 1:1 drilling template for the 125B, standing on end: the face, with the top, left and right walls unfolded beside it. The LED holes are where the board puts them, read off the board's own files, and the dashed outline shows where the board sits behind the face.
The board's four M3 holes are on the sheet as small dashed circles. They are optional: screws through the face into standoffs, or stick-on standoffs and no holes at all.
Print at 100% / “Actual size”, never “Fit to page”, and check the bar measures exactly 4″ before you touch a drill.
Nobody has drilled this one yet, and how far the board sits behind the face is not measured: your standoffs set it. Offer the sheet up to your own box, board and parts before you make a hole.

Circuit from The Popo stripboard guide, every part value the same. Board by Onion Madder.